Wingsuit & Inclined TunnelsNovember 17, 20265 min read

Suits Under Control: Why Ski Jumping Equipment Gets Tested in a Wind Tunnel

139 disqualified jumpers in two seasons, 93% for suit violations — why FIS measures ski jumping suits in a wind tunnel, and what a 2cm difference actually does.

Suits Under Control: Why Ski Jumping Equipment Gets Tested in a Wind Tunnel

Over the 2023–2025 World Cup seasons, 139 male ski jumpers were disqualified from competitions. 93% of those disqualifications were for unregulated suits — not technique, not equipment failure, but a suit that didn't meet the size or permeability limits a jumper is required to compete within. That is not a rounding error in a niche rulebook. It is the sport's single largest source of competitive disqualification, which is exactly why suit measurement in a wind tunnel has become its own specialised discipline.


1. What FIS actually regulates

The International Ski Federation sets two specific limits on a competition suit: air permeability greater than 40 litres per second per square metre , with the difference between the front and back panels no greater than 12 L/s/m² at any point, and a size tolerance of no more than 4 cm larger than the jumper's own body circumference at any given point on the suit. Researchers studying the rules directly have noted something worth stating plainly: these specific limits are not themselves derived from controlled aerodynamic testing — they are regulatory numbers, not measured optima. That gap between "the rule" and "the physics" is precisely why FIS commissioned wind tunnel research to find out what these tolerances actually do to performance.


2. What two centimetres actually costs

The answer, once measured, is not subtle. Published wind tunnel research found that increasing suit circumference by just +2 cm increased drag area by roughly 4% and lift area by roughly 5% . Run through numerical simulation against a 130-metre reference jump, that translated to an average jump-length difference of 5.6 metres — about 2.8 metres of distance per centimetre of extra tolerance . In a sport where World Cup results are routinely decided by fractions of a metre, a suit sized at the legal limit versus one sized conservatively is not a marginal equipment choice. It is a measurable, reproducible competitive advantage, which is exactly the fairness problem the regulation exists to prevent — and exactly why the current tolerance being untested against real aerodynamic data is a live concern for the sport, not an academic footnote.


3. How this is actually measured

The wind tunnel used in this research is itself worth describing, because it defines what "measuring a suit properly" requires: a test section with an 11 m² jet (3.94 m wide by 2.79 m high) , a 5.5:1 contraction ratio , a 10-metre test section , driven by a 2.6-megawatt fan capable of wind speeds up to 83 m/s , with turbulence intensity held below 0.3% . Forces are measured with a six-component balance accurate to ±0.5 N , on a 1:1 scale mannequin — 183 cm, 74 kg, with 19 articulated joints built to reproduce the anatomical geometry a real jumper's body presents to the airflow.

That level of precision is not incidental. A measurement system that can't resolve a 4–5% change in drag or lift area simply cannot answer the question the regulation depends on.


4. Why suits aren't simply regulated to zero tolerance

The obvious-sounding fix — make every suit fit exactly to the body, with no permitted excess — runs into a genuine safety trade-off. Equipment in ski jumping exists partly to balance safety and fairness simultaneously: a suit with more surface area and lift generates aerodynamic support that allows a jumper to fly safely at achievable in-run speeds, while a suit fitted with zero tolerance would require higher, more dangerous in-run speeds to achieve the same flight performance. The tolerance isn't an oversight — it's a deliberate trade-off between two legitimate goals that happen to pull in opposite directions, which is exactly why getting the number right (rather than just having a number) matters enough to commission dedicated research.


5. What this means for equipment manufacturers and compliance labs

  • Permeability and dimensional testing are a repeat-purchase measurement need , not a one-off — every suit design, every athlete's fit, and every season's rule adjustment creates a new item that needs verified data before a jumper can legally compete in it.
  • The measurement precision has to match what's actually at stake. A ±0.5 N balance and sub-0.3% turbulence aren't luxury specifications here — they're the minimum needed to resolve differences that are proven to move real competitive results.
  • A compliance testing programme and a performance-optimization programme use the same equipment for different questions — one confirms a suit meets the legal tolerance, the other explores where inside that tolerance the aerodynamic advantage actually sits.

6. What this means for your programme

Tell us whether you're building for regulatory compliance testing, athlete equipment optimization, or both , and we'll help you specify a facility with the balance accuracy and flow quality this discipline has already proven it needs.


Sources and notes

  • FIS suit regulations (air permeability greater than 40 L/s/m² with front-to-back difference no greater than 12 L/s/m²; size tolerance of no more than 4 cm larger than the jumper's body circumference at any point), disqualification statistics (139 male ski jumpers disqualified from World Cup competitions across the 2023–2025 seasons, 93% for unregulated suits), the finding that current tolerance limits are not themselves derived from controlled aerodynamic testing, the aerodynamic effect of suit size tolerance (a +2 cm increase in suit circumference raising drag area by approximately 4% and lift area by approximately 5%, corresponding to an average simulated jump-length difference of 5.6 m — about 2.8 m per centimetre of added tolerance — for a 130 m reference jump), the wind tunnel facility used (11 m² jet section at 3.94 m × 2.79 m, 5.5:1 contraction ratio, 10 m test section, 2.6 MW fan, wind speeds up to 83 m/s, turbulence intensity below 0.3%, six-component balance accurate to ±0.5 N, 1:1 scale 183 cm / 74 kg mannequin with 19 articulated joints), and the safety-versus-fairness rationale behind suit tolerance: Virmavirta, M., Müller, S., Kürschner, M., Bessone, V., Krężałek, P., Elfmark, O., "Influence of suit size and air permeability on performance in ski jumping. Part I: wind tunnel measurements," Frontiers in Sports and Active Living, 7, 1693699, 2025.
  • Related reading: our published article on
why body position decides more than power in ski jumping

.

Request a Consultation

By submitting, you agree to our privacy policy. We'll never share your data.

Related products & services